Network Telephone Cable Tester Wire Tracker Line Finder Tracer LAN for RJ45 RJ11

Description

Home
Arduino
Module
Sensor
Chips
About Us
NOTE is the warning that may bring the damage or failure to the instrument.
CAUTION is the warning that may be a source of danger to the operator.
CAUTION
Road this manual before operate the instrument
Comply to the instructions, otherwise, the functions may be inactive or weak.
Do not use if the instrument is damaged or the case is fractured.
Do not carry out any measurement in stormy or humid environments.
Do not test high voltage cable circuit (e.g. 220V)
Do not carry out any measurements in case gas, explosive materials or flammables are present, or in dusty environments.
Do not use instrument without battery cover or battery cover installed in a wrong way.
Separate the testing wires from the tested wires before opening battery cover when replacing batteries.
Do not attempt to repair the instrument. The instrument doesn’t include user replaceable parts.
Electricity shock may happen when voltage exceed 30V AC or 60V DC.
P1
BRIEF DISCRIPTION
This instrument is a multi-functional handheld cable testing tool. It has wide application with reinforced cable types and multiple functions. It is a necessary testing tool for telecommunication engineering, wiring engineering and network maintenance person.
Main Functions
Wire tracingTrace RJ11, RJ45, cables or other metal wire (via adapter).
Easy and fast to locate the breakpoint without opening the wire’s cover.
Network cable collation: Judge short-circuit,breaking circuit, open circuit andcrossing.
Test line level, positive and negative polarity.
Status of telephone line checking: Test the working status of telephone line (idle, ringing, and off-hook) and judge TIP and RING line.
Check wire continuity.
General technical parameters
Temperature
Operating temperature:
0 °C ~ 40 °C,
maximal 80% relative humidity (non-condensing)
Storage temperature:-10~50
°C
, maximal 80% relative humidity (non-condensing, battery not included)
Altitude:<2000m( meter)
Anti-explosion rating:IP 40
Distance of emitting signal :300m or so
Safety class:IEC61010 -1 600V CAT III, pollution class II.
Battery
(not included)
Emitter: 6F22/9V; receiver: 6F22/9V
P2
FRONT VIEW & INTERFACES
LED spotlight
Probe
Headset jack
Wire scan indication light
RJ11 terminal
Wire collation indication light
Wire scan power light
RJ45 terminal
Wire scan indication light
Power switch
LED wire sequence light
Status indication light
Volume rotary knob
Function rotary knob
Continuity indication light
Spotlight switch
TEST button
Wire scan switch
LED wire sequence light
RJ45 terminal
Emitter
Receiver
P3
ACCESORIES
1x Clip adapter cable
1x RJ11 adapter cable
1x RJ45 adapter cable
Replace batteries as follows:
Screw out the bolts of battery cover with screwdriver.
Remove battery cover and old battery.
Replace new battery with equivalent specification.
Install battery cover and tighten the back cover with screwdriver.
P4
OPERATION METHOD
Wire Tracing
This function is capable of quickly finding the required line pairs among numerous ones. It is adaptable to network cable RJ 45 terminal, telephone line RJ11 terminal. Via an adaptor can test other metal wires.
Operation method
Turn the emitter’s function rotary knob to
SCAN
Connect one end of tested line to the corresponding terminal of emitter (e.g. RJ45, RJ11 ) or connect to RJ11 terminal via an adaptor.
SCAN
indication light on means emitter starts to send signal to tested wire.
Power on the receiver, hold receiver and press
“SCAN”
button to test the other end of tested line (e.g. near line stacking of telephone line distribution cabinet, terminal box, hub, and exchanger). Compare the sound sent by receiver, the line with the loudest sound close to probe will be the target.
Adjust the volume of receiver by pressing the volume rotary knob during test to adapt to site environment.
Notes: You can connect headset to the headset jack of receiver in places with loud noise.
P5
During scanning, connect RJ11 terminal to RJ11 adapter, any clip of the adapter connect to the computer case or other ground-contacted metal objects.
Network Cable Collation
It tests physical connection status of network cable, such as open circuit, short connection, miswire and reverse connection.
Operation method
Turn the emitter’s function s rotary knob to
Network
Connect one end of network cable to RJ45 socket of emitter, and connect another end of network cable to RJ45 socket of receiver.
Press “
TEST
” button to start test. Line pair indicator lights will tell results.
Short connection: there will be 2 or more lights on simultaneously on the receiver. The lighting quantity indications the quantity of shorted wires.
Open circuit: On the receiver, the corresponding line pair indicator light will not turn on.
P6
Line Level, Positive and Negative Polarity Test
Use emitter only to test line level, positive and negative polarity.
Operation method
Status of Telephone Line Test
Use the emitter only to test the status of working telephone lines.
Operation method to judge TIP or RING line
Turn the emitter’s function rotary knob to
TONE
Connect RJ11 crystal head terminal of adaptor to RJ11 terminal of emitter. Clamp the tested line with a red-black clip.
If telephone line status indicator light is red, the red end is TIP line, and the black end is RING line. If it is green, the red end is RING line and black end is TIP line.
Line level judging: The higher is the level, the higher is the level; The dimmer is the light, the lower is the level.
Operation method to judge whether the telephone line is idle, ringing or off-hook
Turn the emitter’s function rotary knob to
TONE
Connect RJ11 crystal head terminal of adaptor to RJ11 terminal of emitter. Clamp the red clip to RING line and black clip to TIP line.
If telephone line status indicator light is green, it means line is idle; Light off means off-hook; If it is green or red and flashes regularly, it means the telephone line is in ringing.
P7
Continuity Checking
It can check continuity in circuits.
Operation method
Turn the emitter’s function rotary knob to
CONT
Connect RJ11 crystal head terminal of adaptor to RJ11 terminal of emitter. Clamp the red and black clip to the two ends of the tested wire.
“CONT”
light on means the wire is continuous. Less line impedance, the brighter is the light.
Low Battery Capacity indication
Emitter low battery capacity indication: When battery of emitter is lower than working voltage, the power light will flash. It’s time to replace the battery.
Receiver low battery capacity indication: There is a luminous diode on receiver probe, which becomes dim when voltage is low. When the indicator light is very dim, set the emitter to wire scanning and working status, approach RJ45 terminal of emitter with receiver probe, and adjust the volume of receiver till maximum. If there is no sound or very low sound sent by receiver, it’s time to replace the battery.
MAINTENANCE
Do not attempt to repair or service this instrument unless you are qualified to do so and have the relevant calibration, performance test and service instructions.
Periodically wipe the case with a damp cloth and mild detergent. Do not use abrasives or chemical solvents.
Package Included:
1* Network Telephone Line Tracer Tester
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
Fill your shipping info
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.